사막의우물

- Wirelss syncing must be enabled on the summary page for your iOS device in iTunes. It's the second check box under the Restore and a update buttons.

- The checkbox to open iTunes when the device is connected MUST be checked on the summary page as well. It's the first check box under the Restore and Update buttons.

- Your iOS device MUST be connected to a power source to AUTOMATICALLY sync when your on your home network. Yes, you can start a wireless sync manually without being plugged into power by going to Settings > General > iTunes Wifi Sync and tap the Sync Now button.

- You MUST have iTunes 10.5 (or above) installed and open for all of this to happen.

- You MUST be on your home network. You can not wirelessly sync to your home library from work.

If you've done everything above then it should start syncing within seconds of plugging in your device. You should see the spinning arrows in the top left corner. If it still does not work, restart your comp and iDevice. If it still doesn't work, then you have other problems.

Hopefully this helps most people. These seem to be the outcome of most of the "my iDevice doesn't wirelessly sync" threads that keep popping up.

1. 유튜브 플레이리스트 주소를 찾음

(예)http://www.youtube.com/playlist?list=PLxrXSNAnHXeKFXD8qeedKu8Mjr1XjQ8h3

PL이후만 해당됨.

2. RSS 피드주소를 만듬

http://gdata.youtube.com/feeds/base/playlists/"원하는 유튜브 playlist 주소"

(예)http://gdata.youtube.com/feeds/base/playlists/xrXSNAnHXeKFXD8qeedKu8Mjr1XjQ8h3

3. 구글리더 등에 구독 추가함

끝.

(참고 사이트)

http://webapps.stackexchange.com/questions/22056/how-do-i-subscribe-to-a-youtube-playlist

LG G-Slate (V909) 공장초기화

초기화 이후 버전

Android version : 3.0.1

V909-V10p

빌드번호 : HRI66

*초기화 이후, 시스템 업데이트를 통해 3.1로 업데이트 가능함.

준비물

1) 복원 파일(v909_restore.zip) Downloads

2) nvflash 파일(nvflash_new.rar)

https://rapidshare.com/#!download|652p2|738802753|nvflash_new.rar|6993|0|0

준비사항

1) nvflash_new.rar을 압축해제하여, C드라이브 아래에 폴더 위치시킴

2) v909_restore.zip을 압축해제하여, 1)nvflash_new 폴더에 덮어씌움.

Instructions

1. Unzip the v909_restore.zip
• 압축해제하여, nvflash_new 폴더안에 덮어씌움
2. Boot into APX mode.
• Power off the device.
• Press and hold Volume +/-.
• Press the Power button.
• The screen will look like it's off and the device is off, plug it into your computer and it should see the device as 0955:7820 NVidia Corp.
• 드라이버는 아래4번 nvflash_new 폴더 안에 있는 NVidia 드라이버 이용함
3. Unpack the appropriate nvflash.
4. Run the following to restore /system to the stock image: (관리자권한 명령프롬프트)
• 해당폴더로 이동 (nvflash_new 등)/nvflash --bct v909.bct --setbct --configfile flash.cfg --create --bl bootloader.bin --odmdata 0x3b048000 --sbk 0xe3baffc6 0xa9585c23 0xe21b497b 0x793d1932 --go
5. When that is done, reset the device with the reset button under the battery cover.
6. You should now be booting into Honeycomb 3.0.